New handle for an old knife

New handle for an old knife

Today I will tell you how you can make a new handle for an old knife if the original handle has fallen apart. I had a couple of shoe knives, one of which had a handle that cracked and split into two halves.
New handle for an old knife

New handle for an old knife

Making a leather handle


I decided to make a new handle for it, or rather a cover, using leather from the top of old boots.
New handle for an old knife

Having estimated the size of the knife, one tongue was just enough for what was planned. I carefully flogged it and trimmed the edges so that I could wrap the knife plate.
New handle for an old knife

New handle for an old knife

Advice! To avoid cutting myself while working, I sealed the cutting edge of the knife with masking tape, but you can use something else.
New handle for an old knife

The next step is to measure the required length of the handle and cut the leather blank.
New handle for an old knife

Hole preparation


The most important step is preparing and making holes, and you will need a lot of them.
There was a hole at the end of the plate. I decided to leave it and use it later for threading a loop. I marked the centers of the holes on the future handle and punched them using a punch of a suitable diameter.
New handle for an old knife

New handle for an old knife

New handle for an old knife

Now, at equal intervals, you need to mark holes along the edges of the leather piece so that it can be stitched.I used a simple makeshift device: I used an eraser to connect a pencil and a white gel stick so that the marks were clearly visible on the black leather. It was possible to mark quickly and accurately.
New handle for an old knife

New handle for an old knife

After making marks on both sides, I carefully make holes with a punch.
New handle for an old knife

New handle for an old knife

Some may say that this is unnecessary; one could simply pierce the holes with an awl and sew the leather together. But, firstly, it is smooth and neat, and secondly, such round holes are more resistant to tearing. In addition, for stitching I decided to use not harsh threads, but a slightly different material.
New handle for an old knife

Now you need to wet the skin in slightly warm water so that it becomes more elastic and stretches a little. At the same time, you can wash off the previously applied markings. After drying, it will shrink and tightly grip the knife blade.
Note! To prevent the blade from rusting, I lightly lubricated it with machine oil.
New handle for an old knife

Lacing


While the leather was still wet, I immediately started lacing. To do this, I fixed the workpiece in a vice. As a “lace” I used a thin strip cut from a plastic bottle. The lacing was done as usual, but you can experiment with the lace material and type of lacing. I didn’t make a knot at the end of the lacing, but simply hid the ends under a leather cover, lightly greasing them with rubber glue so that they wouldn’t stick out.
New handle for an old knife

New handle for an old knife

New handle for an old knife

New handle for an old knife

The edges of the plastic tape are a little sharp, and the lacing itself is rough to the touch. Therefore, heat treatment is needed to correct this problem. The best option is to use a hair dryer or other heating equipment. But, unfortunately, I don’t have that, so I used hot (not boiling) water.
New handle for an old knife

After soaking the knife in hot water for about 10 minutes, I took it out with tongs and put it in the sun to dry.
New handle for an old knife

When the leather began to dry out, I treated it with a special mastic for caring for leather products. She softened the skin, making it elastic, after which the case fit even better on the handle.
New handle for an old knife

New handle for an old knife

The finishing touch is a leather loop cut from leftover material. The loop complements the leather handle perfectly, and I will also use it to hang the knife on a hook.
New handle for an old knife

New handle for an old knife

The handle fits well in the hand, the lacing does not cut your fingers and provides a pleasant roughness to the contact. The only drawback of such a cover is that you need to make sure that water does not flow under it, otherwise the knife will begin to rust.
New handle for an old knife

New handle for an old knife

New handle for an old knife

Original article in English
come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (4)
  1. Vitaly
    #1 Vitaly Guests 1 September 2018 15:31
    4
    Pampering. It will fall apart along the lacing if used more or less actively.
  2. Guest Sergey
    #2 Guest Sergey Guests September 2, 2018 04:33
    5
    A lot of wasted time and effort on a nonsense craft.
  3. Old friend
    #3 Old friend Guests 2 September 2018 10:54
    1
    where else can I find a hole puncher like this?
  4. Sector
    #4 Sector Guests 12 March 2019 16:55
    1
    If I remember correctly, this is an old Soviet shoe knife. Steel is crap.