Burnishing a knife in citric acid

Burnishing is the process of obtaining a layer of oxide several microns thick. It is also called oxidation, blackening or blueing. This is a dark, almost black coating, but there are other shades.
Basically, bluing is used as a decorative coating, but initially, first of all, it is intended to protect the steel from corrosion.
Burnishing a knife in citric acid

I'll show you a way to make a simple knife bluing at home, using readily available components.
What do you need?
  • - Boiling water 0.5 liters;
  • - Citric acid 50 grams (can be bought at any grocery store).

The proportions are approximate, so it is not necessary to strictly follow them. It all depends on the volume of the container in which you will etch your blade. You need to know that increasing the concentration of citric acid accelerates the oxidation process, but at very high concentrations it can lead to uneven coating.

Knife bluing process


We take glassware the size of the knife blade so that it can be completely immersed in the solution.
Boil water in a kettle. Then we take and carefully pour boiling water into the jar. You have to be careful here, as the can may burst.To prevent this from happening, you can first pour a little boiling water on the bottom and let the jar warm up, then add the rest of the amount.
Burnishing a knife in citric acid

Next, add citric acid to the water and stir thoroughly until completely dissolved.
Before immersing the blade in the solution, it is advisable to wipe it with alcohol to remove all excess grease and dirt.
We plunge the knife blade.
Burnishing a knife in citric acid

After 1-2 minutes, a reaction will begin, which will be noticeable by numerous bubbles.
Burnishing a knife in citric acid

Burnishing will take you approximately 30 to 60 minutes. Everything again depends on your requirements for the color of the coating and the grade of steel of the knife.
During the entire bluing process, you must do the following:
  • - Every 10 minutes, take out the knife and wipe the blade with a soft paper or cloth napkin, removing black deposits from the surface.
  • - Approximately every 1-2 minutes it is necessary to move the blade in the solution, thereby discarding large gas bubbles from the blade. This will ensure even coverage.

Burnishing a knife in citric acid
Burnishing a knife in citric acid
Burnishing a knife in citric acid

After the time has passed, if you are satisfied with the color of the coating, you need to wipe the blade with sunflower oil one last time. This will stop the reaction and make the coating uniform and strong.
This completes the bluing of the knife blade.
Burnishing a knife in citric acid

At the end I want to add:
- Do not inhale pore gases when bluing, as they are harmful. And it’s better to use ventilation if you have it, or at least open a window in the room.
- For a stable process, the water must be hot. Blueing does not take place in cold water. Boiling water is not necessary, but it should be 80 degrees Celsius.

Burnishing a knife in citric acid

If you get small stains, don’t worry, they will go away after the first or second use.
This coating is quite durable and will last for many years.

Watch a video of the bluing process in citric acid


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (6)
  1. Oleg Ivanovich
    #1 Oleg Ivanovich Guests 28 November 2017 22:22
    9
    The article is interesting, but I must note that the alcohol with which the author advises wiping the knife before the described procedure does not remove the fatty film. Alcohol is used for technical purposes for dehydration. To remove the grease film, you must use pure gasoline or solvents.
  2. Michael
    #2 Michael Guests June 28, 2018 08:17
    1
    How to maintain the water temperature for 30-60 minutes?
  3. Dkdance
    #3 Dkdance Guests 26 October 2018 21:43
    3
    For example, you can cut off the top of an aluminum beer can, pour citric acid there, pour boiling water into it and put it on low heat...
  4. valeriyvladimirovich10
    #4 valeriyvladimirovich10 Guests 25 November 2018 06:26
    1
    Very good 👍
  5. Guest Oleg
    #5 Guest Oleg Guests 6 January 2019 14:10
    1
    I tried it with stainless steel, no effect, black steel more or less.
  6. Guest Valery
    #6 Guest Valery Guests 12 March 2019 13:18
    14
    Actually not bluing, but etching. No oxide film is formed; the color of the metal changes for other reasons. And the “harmful gas” that is released is hydrogen in microscopic quantities.