Barrette

In order to make such a hairpin, you will need:
• Three satin ribbons 5 cm wide.
• A piece of organza 25?5 cm.
• Cardboard.
• Scissors.
• Ruler.
• Candle or lighter.
• Moment glue or glue gun.
• Rhinestones, beads.
• Hair elastic (headband, automatic hairpin).

to make a hairpin like this


To begin with, you will have to cut squares (5?5 cm) from ribbons. For convenience, measure the tape with a ruler and mark it with a pencil, and only then cut it off. You need to cut seven of these squares of each color.

cut into squares

cut into squares


Singe the edges of the ribbons so that they do not unravel and it is more convenient for you to work with the fabric.

Burn the edges of the ribbons


You can start folding the petal kanzashi. Connect two opposite corners of the square to form a triangle.

start folding the kanzash petal


Fold the workpiece in half as shown in the photo.

Fold the workpiece in half


Then fold it in half again to create a sharp petal.

fold in half


To prevent it from falling apart, you need to scorch the edge and press it while it is still hot.

singe the edge and press


Trim off the excess and also treat the ribbon with fire.

Trim the excess

Trim the excess


The classic petal for the first row of the flower is ready. Make six more of these petals.

Classic petal


Next, fold the same petals from a ribbon of a different color. You will need seven of them in total.

fold the same petals


For the second row of petals we use a ribbon of a contrasting color, in the photo it is a silver ribbon.

photo this is a silver ribbon


We fold the petal as before, only after the last treatment with fire, press the place where the tape melted with your fingers. And then turn the workpiece out. You should end up with a petal like this.

Folding the petal

Folding the petal


Complete six more of these blanks.

Do six more


All petals are ready. Heat the glue gun and glue the two petals together as shown in the photo below. You can use Moment glue, but then you will have to wait a little longer for the glue to harden.

All petals are ready

All petals are ready


For the base, take a piece of cardboard and cut out a circle with a diameter of 3-4 cm. Stick ribbons on both sides.

take a piece of cardboard


We form the first row of the flower. To do this, glue seven petals in a circle, leaving a little space in the middle.

Forming the first row of the flower


In the second row, also glue seven petals. This time it’s a little closer to the middle.

also seven petals


Now cut 5×5 cm squares from organza and make the same petals as for the second row. There should be only five of them. Then stick them in the middle.

cut from organza


To make the flower even more elegant, make six more petals as for the second row and stick them as shown in the photo.

make six more petals


Make stamens from thin ribbons, as in the first option, or from beads, as in the second. Glue the decoration to a hair tie, barrette or headband.

Hairpin using kanzashi technique

Hairpin using kanzashi technique


Glue rhinestones or one large bead into the center of the flower. The hairpin using the kanzashi technique is ready!

Hairpin using kanzashi technique
come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (0)