How to make a 2 in 1 machine from a hub

For a small workshop, there is nothing better when each tool or machine solves several problems at once. Then even a very limited space will be enough to accommodate everything you need. By making this device, you can simultaneously get a bending machine and a convenient quick-release clamp for a workbench.

Materials:


  • old car hub;
    How to make a 2 in 1 machine from a hub

  • profile pipe 20x20 mm and 15x15 mm;
  • bolts, nuts, washers M10-M14;
  • bearings - 4 pcs.

Manufacturing process of a 2 in 1 machine


From the edge of a section of a 20x20 mm profile pipe 30-50 cm long, you need to make 2 spikes of 30 mm each, and move them apart.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

A hole is drilled in front of them so that it can be screwed to the hub, resting the spikes against it.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

Next, you need to weld the stud to the head of the bolt holding the tube, and the bolt to the hub axis. They are fitted with 2 bearings. If the inner race is large, then bushings are placed. The bearings are pressed on top with nuts through washers.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

The result is bending rollers.
How to make a 2 in 1 machine from a hub

The pipe needs to be drilled from the side closer to the edge opposite to the hub. A nut is welded to the hole.Then a 15x15 mm pipe is inserted into it and tightened with a bolt.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

An elongated M10-M14 nut is welded to the end of the thin pipe. A pin with a transverse hole at the top edge is screwed into it. To drill it, you will need to sharpen it using sandpaper. The hairpin must be equipped with a knob.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

The hub is screwed to the corner of the workbench. By pulling out its rod, you can bring the pin to the desired part of the tabletop and unscrew it, pressing the workpieces.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

Also, by placing rolled steel between the rollers, it can be bent. The strength of the machine is sufficient to work with strip, thin reinforcement and square.
How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

How to make a 2 in 1 machine from a hub

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (0)