How to make a snow shovel from PVC pipe that will be stronger than a store-bought one

It is very convenient to use a plastic shovel to remove snow because it is lightweight and the snow does not stick to it. However, it is almost impossible to find a high-quality tool in a store that would serve well for at least a couple of seasons. But there is a way out, if you have the desire, it is quite possible to make a light, hard and durable shovel with your own hands, which will not wear out and sag under load.
How to make a snow shovel from PVC pipe

Materials:


  • A section of PVC sewer pipe, diameter 200 mm;
  • aluminum or wooden handle;
  • rivets;
  • short screws;
  • lath minimum 50x50 mm;
  • any board with a width of 10 cm.

Making a shovel


To hot mold a shovel, you need to make a wooden mold. This is the most labor-intensive process. A furniture panel measuring 46x46 cm is twisted or glued from the slats. In the front part it needs to be sharpened, making it look like the nose of a shovel.
How to make a snow shovel from PVC pipe

In the absence of a specialized tool, you can cut the slats obliquely separately at the stage of gluing the shield, and then straighten the slats with a plane already in the shield. The ends of the mold are chamfered.You also need to cut 4 longitudinal spikes on it, which will form stiffening ribs. Instead of cutting tenons, you can simply stuff 4 thin slats on top. A rounded groove is made in the center of the form to tightly fix the handle. To round it, you can heat a steel blank red-hot and burn out the wood, having previously made a selection in place with a chisel. A board edging is placed around the perimeter of the form.
How to make a snow shovel from PVC pipe

A 40 cm piece is cut from the sewer pipe. A longitudinal cut is made along it. The material is perfectly cut with a grinder, and it does not melt, of course, if a good pipe with a wall thickness of 4 mm is used.
How to make a snow shovel from PVC pipe

Next, you need to turn on the hair dryer to maximum and evenly heat the workpiece from the inside. To avoid getting burned, it is better to work in two pairs of thick gloves.
How to make a snow shovel from PVC pipe

As the pipe warms up, it will begin to straighten. You need to give it a flat shape.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

To do this, the softened material can be pressed down on top until it cools with a piece of plywood, a door or a shelf from an old furniture. When blowing with a hairdryer, you should not linger in one place, as bubbles and burnt areas will appear on the overheated plastic.
Then the flat blank is screwed with several self-tapping screws to the edging of the front part of the mold.
How to make a snow shovel from PVC pipe

Next, the plastic is heated around the entire perimeter. The softened areas must be pressed onto the mold until they cool.
How to make a snow shovel from PVC pipe

To prevent them from straightening back out, their edges should be screwed to the edging.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

Having given the workpiece the outline of its shape, you need to squeeze out the stiffening ribs and rounding for installing the handle. To do this, the plastic is heated in place and pressed with a block on the ribs and a handle in the center.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

A stiffening plate is cut out and bent from a small piece of PVC pipe to strengthen the place for fixing the shovel handle.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

To fasten the plate to the shovel, you need to drill holes around their perimeter and put rivets in them. The workpiece is removed from the mold. Excess plastic around the edges is trimmed with a grinder.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

Next, all that remains is to insert the handle and drill a through hole in the shovel to secure the handle with a bolt. The result is a strong, rigid tool that can be used to throw wet snow and even scrape off melted ice. Of course, it will take several hours to make it, but such a shovel really won’t break when clearing snow.
How to make a snow shovel from PVC pipe

How to make a snow shovel from PVC pipe

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (6)
  1. Michael
    #1 Michael Guests 7 December 2019 19:50
    6
    It's possible, but it shouldn't be done.
  2. Dispatcher
    #2 Dispatcher Guests December 7, 2019 21:34
    2
    nightmare. Energy costs are not counting time and effort.
  3. Guest Sergey
    #3 Guest Sergey Guests December 8, 2019 11:13
    2
    What nonsense. During this time and labor costs, you can earn enough for 2-3 shovels and buy
  4. Vlad
    #4 Vlad Guests 9 December 2019 15:18
    4
    This is for people with a lot of free time.
  5. Guest Vladimir
    #5 Guest Vladimir Guests 26 February 2020 10:52
    0
    To make a shovel, which costs 200 rubles. I also need to buy a hairdryer for 2000 rubles. Profitable.
  6. Airat
    #6 Airat Guests 21 February 2022 14:29
    0
    I like it. I'll try to use the material, but the design is simpler and less energy-consuming...