How to restore a car wheel if damaged by a curb

Curbs pose a serious danger to car rims. Light alloy products suffer especially badly from them. If a crack or crease occurs, you must contact a specialist.
Defects in the form of scratches, abrasions and shallow local dents can be removed independently, without even removing the wheels from the car and at the same time significantly saving the family budget.
How to restore a car wheel if damaged by a curb

Will need


For work you need the following materials, devices and tools:
  • finishing putty;
  • a can of aerosol paint;
  • plastic spatula;
  • sandpaper P80 and P180;
  • non-woven abrasive material (Scotch-Brite);
  • paper napkins;
  • thin screwdriver;
  • construction tape and plastic film;
  • pieces of cardboard.

The process of repairing a disk damaged by a curb


Inspection of the cleaned disc shows that two spokes and the rim between them are damaged. They spoil the appearance, but what’s even worse is that the disk will quickly begin to deteriorate and may become unfit for further use.
We start by sanding the damaged areas with coarse-grained P80 sandpaper.We grind vigorously to smooth out sharp edges, but carefully to avoid noticeable disruption of the three-dimensional shape of the processing areas.
How to restore a car wheel if damaged by a curb

After sanding, you can see that there are recesses that need to be hidden. To do this, we use finishing putty, for example, the “U-Pol Top-Stop” type, which we apply with a plastic spatula. Let the putty dry for 30 minutes.
We check the degree of hardening of the putty by trying to leave a mark on it with a fingernail. If this cannot be done, then it is ready for further processing.
How to restore a car wheel if damaged by a curb

First, we sand the putty with P80 sandpaper, and finish with P180 sandpaper. After this operation, there should be no protrusions or depressions in the damaged areas, and the putty layer should follow the three-dimensional shape of the disc and smoothly move to the undamaged areas.
How to restore a car wheel if damaged by a curb

Before painting, remove shine from the disc using Scotch-Brite, which is a non-woven abrasive material. We complete this operation by wiping the disk with paper napkins.
To prevent the paint from getting where it is not needed, remove the cap with the emblem of the car brand from the hole in the hub by prying it off with a thin screwdriver. We seal the sockets of the bolts securing the wheel to the hub and the chamber valve with pieces of tape. Cover the brake disc with pads with plastic wrap. We protect the tire with pieces of cardboard, inserting them into the gap between the tire and the disk.
How to restore a car wheel if damaged by a curb

To paint, we use a can of aerosol paint, which we apply evenly over the entire surface of the disc. Give 10 minutes for the paint to dry. Then apply a second coat of paint. Let stand for 30 minutes.
How to restore a car wheel if damaged by a curb

If after this, any defects are noticeable on the disc, then we treat the surface with fine-grained sandpaper and apply a layer of paint again.After it has dried, cover the disc with colorless varnish and also wait for it to dry.
After this, you can remove all protective materials, replace the hub cap and make sure that the disc is as good as new.
How to restore a car wheel if damaged by a curb

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (0)