Restoring carvings using the old-fashioned method

This method of restoring carvings was shown to me by my father at one time, and to him by his father (my grandfather). Damage to threads in holes, especially when they are made in parts made of aluminum, magnesium or copper alloys, occurs quite often. This problem is encountered en masse at repair plants, service stations, at home, etc.
Restoring carvings using the old-fashioned method

It may turn out that you do not have a tap of the appropriate size at hand, and the part with damaged threads is bulky and firmly attached to a machine or mechanism, for example, like a clutch housing to an engine and gearbox.
It seems the situation is hopeless. But it turns out that there is a fairly simple but effective way to restore the threads in place using an ordinary steel bolt of the appropriate size, even possibly unscrewed from the same damaged hole.
To implement this method, we will need a mini grinder with a small and thin disk. If it is missing, then you can get by with an ordinary hacksaw for metal, since in principle there is nothing to saw.Here are some specific examples of using this method of restoring internal threads.

Restoring car exhaust manifold threads


Imagine an exhaust manifold that is secured to the engine block with bolts or studs in several places. Damage to even one hole in such a part poses a significant problem. Even disconnecting this unit from the engine is often difficult: over many years of operation, due to high temperatures, it becomes tightly stuck to its seat. And then you still need to find a craftsman with the right tap, pay for the work...
There is only one thing left: fix the problem yourself, since a crumpled profile in the hole will not allow you to screw a bolt into it, and may even ruin the thread on it.
Restoring carvings using the old-fashioned method

Restoring carvings using the old-fashioned method

You can use the “native” one, just unscrewed, or another one, but exactly the same in size and profile.
We clamp its head in a bench vice so that the rod points upward. Then, using a hacksaw for metal, we cut a groove of about 3-5 turns exactly in the center of the rod.
Restoring carvings using the old-fashioned method

Next, generously lubricate the cut bolt and the damaged area with machine oil, and screw this kind of tap into it, first by hand as far as you can, then with a wrench, screwing it in and out several times in a row.
Restoring carvings using the old-fashioned method

Restoring carvings using the old-fashioned method

As a result, the threaded protrusions on the bolt, cut by a groove, fit into the recesses and gradually cut off the creases.
Restoring carvings using the old-fashioned method

After unscrewing our unique tap, we are convinced that it itself remains intact, and what is even more important, it has completely restored the profile in the hole.
Restoring carvings using the old-fashioned method

Now you can screw this or another similar bolt into it completely with one hand and secure the part in the place intended for it.
Restoring carvings using the old-fashioned method

Hood hinge attachment


Sometimes this defect occurs in the hole to which the hood hinge is attached. We do exactly the same as with the exhaust manifold.
Restoring carvings using the old-fashioned method

We fix the fastening bolt in a vice and make a groove on its rod, adding lubricant, after which we tighten it by hand as long as possible.
Restoring carvings using the old-fashioned method

Next, we continue the process using a wrench, screwing and unscrewing the homemade tap several times.
Restoring carvings using the old-fashioned method

At the same time, the cut profiles of its thread tidy up the profile in the hole, performing the functions of a tap. By removing the bolt, you can make sure that the threads on it and inside are in perfect order. The bolt can now be easily screwed into it by hand. If you then tighten it with a wrench, it will provide the necessary tightening force.
Restoring carvings using the old-fashioned method

Restoring carvings using the old-fashioned method

Restoring threads on an engine block


The problem in question can also occur on the engine cylinder block, especially if it is made of aluminum alloy. A clogged or crumpled thread in the hole prevents the bolt from being installed properly. He either doesn’t screw in or tends to go wrong.
Restoring carvings using the old-fashioned method

We repeat the procedure we used with the exhaust manifold and the hood hinge assembly. The rod of a bolt clamped in a vice is cut from the end with a hacksaw for metal to a depth of several turns.
Restoring carvings using the old-fashioned method

Then, having removed metal particles from it and generously lubricated it, we screw it by hand into the hole with damage. As soon as the bolt is securely in there a few turns, we take the wrench in our hands and carefully and gradually screw it in and out until we go all the way to the end.
Restoring carvings using the old-fashioned method

We make sure that the thread in the hole has been restored and that it has not been damaged on the bolt. You can prove this by screwing it into place to the full depth by hand.
Restoring carvings using the old-fashioned method

Conclusion


Considering that millions of bolts are produced every day in the world, this surprisingly simple method of restoring threads in holes can be considered an outstanding technical solution.

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (8)
  1. Guest Yuri
    #1 Guest Yuri Guests 17 May 2019 20:48
    5
    Why do it simple (with a tap) when you can do it complicated? Are they all so gifted in Ireland?
  2. Guest Nikolay
    #2 Guest Nikolay Guests 18 May 2019 04:44
    0
    I think in the past it was relevant due to the lack of markers. but nowadays the required tap is not a problem. and the quality of the thread will be much better.
  3. Eugene
    #3 Eugene Guests 19 May 2019 18:35
    3
    This happens in our general store, God forbid, and then we ran around to friends looking for taps and extension cords for them. And here - did you want to do something new? You can't do this on the road anyway. A set of simple taps was always easier to find with us back then.
  4. Guest Sergey
    #4 Guest Sergey Guests 29 June 2019 22:05
    1
    The method may not be bad, if not for the but. 1. The thread entry is clogged - the original bolt will no longer fit without a cone.2. Difference of metals.When cutting a bolt, burrs remain and the old thread can simply be licked off in the duralumin.
  5. Igor Yaroslavsky
    #5 Igor Yaroslavsky Guests 9 July 2019 10:10
    1
    Usually, when you unscrew a stuck bolt, you also pull out the thread, so this method is for those who do not have money for a tap.
  6. Ponomarev Yuri Dmitrovich
    #6 Ponomarev Yuri Dmitrovich Guests 2 August 2019 22:31
    4
    Change your car and don't fool yourself!!!
  7. Oleg.
    #7 Oleg. Guests August 3, 2019 04:07
    2
    If a blind hole tap does not help, it will cut the thread to half the depth.
  8. ALEKSEI
    #8 ALEKSEI Guests December 18, 2020 11:40
    3
    After you have done all this, it is not necessary to sell both the sawn bolt and the damaged part for scrap metal.