How to repair a hole in slate

Where the holes in the slate come from, when there are no trees or tall buildings nearby from which something could fall, remains a mystery to me personally. And yet it is a fact. Nowadays, many varieties of various adhesives are sold for a wide variety of materials, including slate. However, many of them are not as effective as we would like. Some flow down from the roof along with the rain during a downpour, others, at best in the spring, along with the snow. In the end, I decided to make the glue myself, with my own hands. The glue turned out good. Patches using it successfully survived the winter and are still doing their job. Having crawled the roof in the spring in search of new “surprises”, and was surprised to find the patches intact, I decided to share some useful advice. This is what the one year old patch looked like.

It was not without difficulty that I tore it off to clearly show how to install a new one.

Will need

  • PVA glue.
  • Alabaster.
  • Asbestos fabric.
  • Bicycle wheel spokes (or similar wire).
  • Sandpaper for wood (coarse grain).

Fixing a hole in the slate

Our patch will be reinforced.Therefore, first we will prepare knitting needles (if you don’t have them, cut steel wire) and asbestos fabric. Now let's dilute the glue itself. Pour 180-200 grams of PVA glue into the bowl in which we will knead. Next, add alabaster in small portions, stirring continuously, until the mass acquires the consistency of thick sour cream.

After the mixture is ready and there are no lumps left in it, we immerse the prepared asbestos patch into the mixture.

You can leave the mixture alone for ten minutes, let it brew. During this time, we will prepare the site for the future patch. Using coarse sandpaper, we clean the areas around the hole to the entire area where the mixture will lie.

Lubricate the sanded surface with PVA glue. Now we take two or three knitting needles and place them on the hole, along the edges of the slate.

On top, on the knitting needles, we apply an asbestos patch soaked in the mixture. Next, spread the mixture around the patch in an even layer. Level with a spatula. We close the container with the mixture with a lid so that it does not start to dry out and wait an hour and a half until the patch sets slightly. Then we fix the patch with a second layer, not too thick.

You can lightly sprinkle alabaster on top. It will take a day to dry, so before you start work, find out the weather forecast for the next day, since even light precipitation can ruin all your work. But then you can safely forget about the hole until you decide to change the covering on the roof.

come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (9)
  1. Sergey K
    #1 Sergey K Visitors 13 June 2018 17:10
    2
    PVA, of course, seems to be waterproof, but alabaster definitely doesn’t like water very much...
    Wouldn't it be better to mix this whole thing with modern cement-based adhesive mixtures? Coat it well with a primer, and you can even take a regular cloth and smooth everything carefully.
  2. Guest Sergey
    #2 Guest Sergey Guests 13 June 2018 19:15
    5
    You can make universal glue. Take acetone and polystyrene foam. Pour acetone into some kind of container, add polystyrene foam. The foam will dissolve. Make it as thick as glue. Please note it dries very quickly. to glue cracks, take a construction mesh. The smaller the square, the better. Spread the pre-cleaned surface with glue, apply the mesh and spread it over the mesh.
  3. Guest Mikhail
    #3 Guest Mikhail Guests 15 June 2018 22:37
    2
    Take a piece of galvanized steel, a couple of centimeters larger than the hole along the bend. Bend along the wave of slate. Silicone the galvanized perimeter and holes. Then screw the galvanized sheet with self-tapping screws and a press washer (with a drill) Silicone self-tapping screws. No need to wait for anything, do it and forget it.
  4. Guest Mikhail
    #4 Guest Mikhail Guests 15 June 2018 23:18
    2
    Tested many times. Alabaster + any paint - old thick. Mixed into a thick dough. And any holes are sealed. On dry slate...
  5. Guest Victor
    #5 Guest Victor Guests 16 June 2018 14:37
    1
    A reliable method. Cement 1 part, asbestos 7 parts. Loosen sheet asbestos, mix with cement and add water until it becomes a thick porridge. This is slate.
  6. Ramils
    #6 Ramils Guests June 23, 2018 12:27
    1
    I repaired the slate like this:
    I took burlap, polyethylene, epoxy resin with a hardener.
    I laid polyethylene over the hole in size, and on top - burlap, slightly larger in size than polyethylene. The burlap was impregnated with epoxy and hardener. Be sure to cover the edges of the burlap with glue and press it against the slate.
    4 years old, like new.
  7. Guest Andrey
    #7 Guest Andrey Guests July 8, 2018 09:45
    0
    Ahaha, now bring on the lower wave!
  8. Guest Alexander
    #8 Guest Alexander Guests 20 September 2018 13:45
    1
    Place a plastic container. Dilute the cement very quickly with silicone glue and quickly cover it. The solution sets very quickly. I’ve known this recipe for about 50 years. I once used this solution to put a toilet on. I so cursed the day I learned this recipe.
    1. Volka
      #9 Volka Guests October 11, 2018 11:24
      2
      You made a mistake in the text - the glue is silicate, not silicone.