Simple DIY keyboard backlight

When typing in the dark, be it text or correspondence on the Internet, you always end up not understanding what. I do not have touch typing. So I'm constantly looking for a way to backlight the keyboard. My previous designs were worn out by time and helped by a small child.
The design will have height adjustment. There is no need to make it particularly high.
Everything is made from available, not rare parts.
For production we will need:
  • - axis from the printer;
  • - halogen lamp;
  • - a piece of LED strip;
  • - two-wire wire;
  • - pin;
  • - single-core copper wire;
  • - plywood or chipboard;
  • - epoxy adhesive;
  • - drill, soldering iron, self-tapping screws.

Making a backlight for a computer keyboard


To begin with, the printer axis needs to be freed from the rollers. They fit very tightly, but if you help with a hammer, they come off quickly. As a last resort, you can cut it down. The main thing is not to damage the axle coating; it will quickly become covered with rust.
Simple DIY keyboard backlight

On a single-core copper wire, mine is a 2.5 square mm mounting wire, we make a ring for a 4 mm screw. Set aside at this stage.
Simple DIY keyboard backlight

I took the power cord about one and a half meters. A large cross-section of wire is not needed, the current is small.I have a double wire with a core diameter of about 0.25 square mm. I applied what I have, maybe thinner. The backlight is powered by 12 volts taken from the computer power supply. The wire is simply inserted into any hole in the system unit and connected to the black and yellow wires. You can also power it from an external power supply of 12 volts and current for a lamp or LED strip.
Simple DIY keyboard backlight

The reflector of this design is very convenient. We take a burnt, or maybe a new, halogen lamp and carefully knock out the glass. Be careful, the glass may bounce into your eye, follow safety precautions.
Simple DIY keyboard backlight

Cut a piece of 40-60 mm from a single-core wire. We make a bend at the end and insert it into the reflector. We also insert the power cord there. Fill all this with epoxy glue. Once frozen, the wires sit securely and will not fall out.
Simple DIY keyboard backlight

For aesthetics, we will make a twisted wire. I will have it hanging around the lighting stand. During the manufacture of the structure, another axis was taken from the printer; it had diameter transitions. Cutting them off exposes the axle to rust. So I took another axis.
To make a twisted wire, you need to wrap the wire tightly around the axle and heat it up. I did this with an industrial hair dryer, you can heat it over a gas stove. Set aside the wire to cool.
Simple DIY keyboard backlight

We glue a piece of LED strip into the reflector. We protect the wires and solder them. The double-sided tape turned out to be bad, so I glued the tape with super glue. Holds up great.
Simple DIY keyboard backlight

I make the basis of the structure from various chipboard scraps. It can be made from anything: plywood, OSB, etc. I make it in a round shape. I cut with a crown on plywood and drywall.
The middle ring is in the shape of a donut; a switch and some wires will be installed there.
Simple DIY keyboard backlight

I processed the base blanks and twisted them together.At the end of the middle piece, a donut, I made a slot for a switch.
Simple DIY keyboard backlight

I made a hole in the top circle; the power wire will be inserted there later. Between the lower and middle circles I drilled a hole for the wire. Drilled at an angle.
Simple DIY keyboard backlight

I was thinking about painting. I decided to paint it matte black.
Simple DIY keyboard backlight

I attach the power switch with epoxy glue. You don’t need a lot of it, if the glue is good, it will stick with a small amount.
Simple DIY keyboard backlight

While the glue hardens, we proceed to assembling the reflector. I drill a through hole in the clothespin. Using a 4 mm screw, we twist everything into one, not forgetting about the grower.
Simple DIY keyboard backlight

We pass the wire into the hole, having first screwed the wire onto the axle. We strip the wire insulation and cut one wire. We solder the resulting wire break to the switch. Let's isolate.
Simple DIY keyboard backlight

We twist the base into a single structure.
Simple DIY keyboard backlight

We test by temporarily connecting it to a 12 volt battery.
It turned out great. Adjustable in height to fully illuminate the keyboard.
Simple DIY keyboard backlight

This is such an excellent backlight for the keyboard. There is more than enough light. In general, I advise you not to throw away such reflectors, which are very useful after they burn out.
Simple DIY keyboard backlight

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (7)
  1. Sidor Lyuty
    #1 Sidor Lyuty Guests March 4, 2018 06:58
    7
    They piled up a bunch of nonsense. Just take Chinese Light-emitting diode, connect it to the USB port and pull it Light-emitting diode a piece of PVC tube so that it doesn’t blind your eyes and attach it (or even with plasticine) to the top of the monitor.
    1. popvovka
      #2 popvovka Guests March 4, 2018 09:55
      0
      And a piece of tube to the monitor with plasticine is not nonsense, it made me laugh))
  2. Kamerunec
    #3 Kamerunec Guests March 4, 2018 07:12
    0
    Why load the power supply with halogen, there are super bright diodes.
    1. popvovka
      #4 popvovka Guests March 4, 2018 09:57
      1
      Did you even read the article? A piece of LED strip with a current of 50 milliamps, this is the power supply load.
  3. Pavel
    #5 Pavel Guests July 31, 2018 01:23
    2
    Honestly, it looks like it was picked up from a trash heap)))
  4. Sergey_143
    #6 Sergey_143 Guests 1 March 2019 14:13
    0
    A table lamp is also not a bad option, but an LED strip would be better for my table.

    I made a brightness control for the keyboard backlight. I collected it according to this scheme:

    Unfortunately, I don’t remember the resistor values; I assembled the circuit a long time ago. The switch next to the regulator is made for the second illumination of the table. The keyboard backlight turns off automatically when you slide the board into place. There is no sensor, just a regular button from a computer mouse.
  5. Continent Telecom
    #7 Continent Telecom Guests 26 October 2022 16:06
    0
    Your message is simply lovely