How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

For quick, comfortable drilling at right angles, you can make a drill stand for a drill. Many parts for this are easy to find at a metal receiving station, so the cost of a homemade product is several times lower than its factory counterpart.

Basic materials:


  • profile pipe 20 mm;
  • double-row roller chain;
  • double-row sprocket;
  • corner 30x30 mm;
  • strip 30 mm;
  • rod 6-10 mm;
  • bolts, nuts;
  • extension springs – 2 pcs.

Drill stand manufacturing process


A frame for the sole of the machine is welded from a profile pipe.
How to make a drill stand for a hand drill from a roller chain

2 crossbars made of a square rod are welded into it.
How to make a drill stand for a hand drill from a roller chain

A section of 40-50 cm profile pipe is used as a machine stand. A double-row roller chain is welded to it.
How to make a drill stand for a hand drill from a roller chain

Next you need to make a carriage with a mount for a drill. To do this, a U-shaped profile is welded onto a stand from a corner and a strip. When welding, you will need to place a sheet of paper between the parts to create a gap.
How to make a drill stand for a hand drill from a roller chain

2 eyes with holes are made from the strip. A bolt with an asterisk is inserted into them. To prevent turning, they are welded.If the width of the sprocket is not enough, you will need to place washers on the sides of it. The lugs are welded to the carriage profile.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

From the front side, the carriage is welded with a piece of strip. Small bolts are welded on the sides of the U-profile.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

A clamp is made from a ring cut from a pipe onto the drill body at the location where the handle is installed. It is welded to the carriage.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

3 rods with a headband of bearing balls are welded onto the head of the bolt holding the sprocket. At the point of convergence, a small star or washer is welded onto them for rigidity. This creates an adjustment wheel.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

The stand is welded to the sole at a right angle. A carriage is put on it. At the top of the rack there is a through hole through which a pin is passed. Between it and the bolts on the carriage it is necessary to tighten 2 return springs.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

The machine is being painted. A large star or plate is screwed to its base to form a support table. The drill is clamped in the clamp. That's it, the drilling machine is ready for use.
How to make a drill stand for a hand drill from a roller chain

How to make a drill stand for a hand drill from a roller chain

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (0)