How to make a penny pipe cutter from PVC pipes and for PVC pipes

In order for the cut sewer pipe to fit into the socket, it must be chamfered. As a result, preparing each trim takes time. If you make a pipe cutter of this design, then each piece will immediately have a chamfer.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

Materials:


  • enlarged clamp;
    How to make a penny pipe cutter from PVC pipes and for PVC pipes

  • an old screwdriver with a removable shaft;
  • pipe socket 110 mm;
    How to make a penny pipe cutter from PVC pipes and for PVC pipes

  • flat bit for a screwdriver;
  • plastic dowel.

Pipe cutter manufacturing process


On the bell it is necessary to cut 4 petals 20 mm wide with the same distance from each other. They should go from the beginning of the bend to the narrowing of the socket to the diameter of the pipe. It is convenient to make holes at the boundaries of the markings and cut everything out with a jigsaw to them.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

Next, you need to cut off the step at the entrance to the socket and remove the sealing gum. The petals must be heated with a burner and bent inside the bell.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

Their protruding part on the back is cut off. The previously cut end is ground flat.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

A dowel is inserted into the screwdriver handle. Then it is screwed onto the screw of the clamp.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

You need to drill a 6 mm hole at the edge of one of the clamp's whiskers.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

A triangular cutter is machined from a bit. It is pressed into the hole in the clamp with the tip inward. To prevent the plastic from splitting, it is better to do this in a vice rather than hitting it with a hammer.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

To cut a pipe, you need to put a stopper from the socket on it. Next, the clamp is tightened and aligned with a cutter along the markings for cutting.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

The clamp rotates on the pipe by the handle until the cutter almost passes through the wall. Finally, you need to cut the pipe with a mounting knife. As a result, the cut piece and the rest of the pipe will have a neat chamfer, so they can easily fit into the sockets.
How to make a penny pipe cutter from PVC pipes and for PVC pipes

How to make a penny pipe cutter from PVC pipes and for PVC pipes

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (0)