Making a wall-mounted compact boxing trainer from a tire

To practice punches and kicks, you can make a very simple wall-mounted simulator from a tire. It has a simple device that allows you to do it in literally 1 hour.
Making a wall-mounted compact boxing trainer from a tire

Materials:


  • plywood;
  • a car tire, preferably with a heavily worn tread;
  • wood screws;
  • washers;
  • dowels or anchors.

Making a wall-mounted compact boxing trainer from a tire

The manufacturing process of the simulator


It is necessary to measure the diameter and width of the tire. Based on the obtained dimensions, a base is cut out of thick plywood for installing half of the tire. It is made in the form of a rectangle. Its width should be 30-40 cm larger than the diameter of the tire, and 20 cm wider. After trimming, the plywood is sanded and the chamfer is removed from it.
Making a wall-mounted compact boxing trainer from a tire

Holes are drilled for future wall mounting.
Making a wall-mounted compact boxing trainer from a tire

You can also paint it; this will not hurt if you plan to install the exercise machine outdoors.
Making a wall-mounted compact boxing trainer from a tire

The tire is cut into 2 parts with a grinder, so as to form eyelets for fastening along its edges. When cutting with a grinder, there will be a lot of acrid smoke, so it is better to do it outside. It is cut across the tread, then along the line of the sidewalls 10 cm in a smaller direction.The cut to the bead is made at a slight angle from the cross-section of the tread. If there is no plywood of sufficient size available, then when cutting the tire, you can make a cut less than half, adjusting it to the existing base.
Making a wall-mounted compact boxing trainer from a tire

Making a wall-mounted compact boxing trainer from a tire

Making a wall-mounted compact boxing trainer from a tire

Next, half of the tire with lugs is screwed to the plywood base. For this, self-tapping screws with washers are used, which will prevent rubber breakthrough. 4 screws on each side will be enough.
Making a wall-mounted compact boxing trainer from a tire

Making a wall-mounted compact boxing trainer from a tire

Then the simulator is screwed to the wall through the previously made holes in the corners of the plywood. Depending on the wall material, hanging is done using nylon dowels, metal or chemical anchors. The height of the simulator is selected according to the height of the trainee.
Making a wall-mounted compact boxing trainer from a tire

Making a wall-mounted compact boxing trainer from a tire

To practice striking techniques, it is advisable to use gloves or at least bandages. The shape of the simulator allows you to practice direct strikes, from below, from the side. When training without gloves, you should try to be in the center of the tread, where the rubber is softer. The simulator is also suitable for practicing kicking techniques; it is especially convenient to perform straight kicks. The second part of the tire can be saved and later, if necessary, cut off and used for replacement when the first half breaks and loses its shape. The actual service life of the simulator from the tire is very long, so the second part can be thrown away, since new worn tires will appear before the first is replaced.
Making a wall-mounted compact boxing trainer from a tire

Making a wall-mounted compact boxing trainer from a tire

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (0)