How to make a belt grinder using a grinder without welding

A belt sanding machine can be used for sharpening knives, axes, chisels, sharpening blades, turning workpieces, removing rust and solving dozens of other problems. This is an irreplaceable piece of equipment, but even it may be too large for a small workshop. Having a lack of free space in the workplace, you can make a homemade belt grinder based on a 125 mm angle grinder. Such a machine turns out to be very compact and inexpensive to manufacture, and the grinder used as its drive, if necessary, can be removed and used in normal mode.
How to make a belt grinder using a grinder without welding

Necessary materials


The choice of materials and their quantity depends on what kind of sanding belt you plan to use. It’s better to make a grinder for tape of standard sizes available for sale, so that you don’t have to cut the paper and glue it yourself. For a grinder based on an angle grinder, a belt with a width of 40, 45, 50 mm is suitable.
Having decided on the tape, you can prepare other materials:
  • extended nut M12;
  • timber or board with a thickness corresponding to the width of the tape;
  • two-component epoxy adhesive;
  • steel plate or wide strip with a thickness of 5 mm or more;
  • steel corner 50x50 mm or larger;
  • M6 bolts;
  • M10 bolts;
  • M10 nuts;
  • bearings 3-4 pcs.;
  • extension spring.

Making a Belt Sanding Machine


First you need to make a drive roller to rotate the belt. It can be drilled with a crown with a diameter of 40-50 mm from a block or board.
How to make a belt grinder using a grinder without welding

In this case, the width of the roller must be equal to or greater than the width of the belt. On one side, its central hole needs to be drilled out and an elongated M14 nut pressed into it using epoxy glue.
How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

After the glue hardens, the roller is installed on the grinder. Next, you need to turn on the angle grinder and sand it, pressing it against sandpaper. You need to give it a barrel shape, slightly pressing the edges and leaving the central diameter. In this case, the tape will then fly off.
How to make a belt grinder using a grinder without welding

The grinder frame is cut out of a strip or steel plate. Its dimensions will depend on the length of the selected sanding belt standard.
How to make a belt grinder using a grinder without welding

A hole with a diameter of 40-45 mm is made in the frame. The grinder gearbox will be inserted into it and the shaft will be removed.
How to make a belt grinder using a grinder without welding

To mark the fasteners, you need to temporarily remove the gearbox, place it in place and mark the holes for the screws.
How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

4 mounting holes and 2 grooves on the side are made in the frame so that when docking it does not interfere with the screws that press the gearbox to the angle grinder body.
The machine stand is made from two corner pieces.
How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

The frame is clamped between them with bolts in a vertical position. To do this, holes are made for 3 M6 bolts, in which threads are cut. You will also need holes in the bottom of the stand to screw the machine to the table.Having secured the frame, you can try on the angle grinder, but the standard screws on its gearbox need to be replaced with elongated ones.
How to make a belt grinder using a grinder without welding

Next, a shoulder is cut out to tension the tape. It is attached to the frame in the center with an M10 bolt and nut.
How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

A second M10 bolt is placed at the end of the arm, pressing 3-4 bearings. It is necessary that the width of the bearing group corresponds to the width of the tape. They will perform the function of a driven tension roller.
How to make a belt grinder using a grinder without welding

To tighten the resulting roller, a spring is placed on the second end of the arm, engaged at the bottom of the frame.
How to make a belt grinder using a grinder without welding

How to make a belt grinder using a grinder without welding

An adjustable stop plate is cut from the corner, as in the photo. It should have a groove to allow it to change position when clamped.
How to make a belt grinder using a grinder without welding

Also, a working platform is made from a steel plate and a small corner. You also need to make a groove in its corner to be able to adjust the position.
How to make a belt grinder using a grinder without welding

The stop and working platform are screwed to the frame with M6 bolts. After tensioning the sanding belt, the machine can be used for its intended purpose. It can perform absolutely the same tasks as a factory grinder. When not needed, the machine can be disassembled and folded compactly. The angle grinder used with it is not subject to design changes, so it can still be used for its main purpose.
How to make a belt grinder using a grinder without welding

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (3)
  1. Alex Sirs
    #1 Alex Sirs Guests 5 January 2020 20:11
    1
    Doesn't 20,000 rpm bother you?
    1. Yuri
      #2 Yuri Guests January 6, 2020 01:00
      2
      Where will this 20,000 come from? The angle grinder 125 has a typical speed of 11,000 rps, which on a roller with a diameter of 50 mm will give a belt speed of 32 m/s. Some materials require even higher speeds. In addition, 11000 is at idle, and with a 125 angle grinder everything is very bad with torque, so under load the speed drops considerably.
      Well, no one forbids using a speed controller.
      1. Yuri
        #3 Yuri Guests 6 January 2020 17:29
        2
        "11000 rps" is a typo. I meant 11,000 rpm, of course. But all other numbers are correct.