Plywood car model


Do you like working with wood? Then this is especially for you! Today I will show you how you can assemble a model of an old car from plywood. So, let's begin. First you need to cut out the following blanks with a jigsaw:
This is the foundation of the entire car. The left part is the front part.

Here we will add a roof to give you a rough idea of ​​the proportions.

This is the left and right side of the car.

These are wings. You also need two of them.

Four wheels with locking caps.

Side surfaces of the engine compartment.

Rear of the car. The so-called back. Performed in a single copy.

I don't know what to call this. Installed immediately behind the radiator trim. In general, you will see


This is the panel between the passenger compartment and the engine compartment. All cuts must be made very carefully!


This is the engine compartment cover - the hood. It is necessary to carefully bend the plate, as shown in the photo.

And these are two headlights and a steering wheel. The steering wheel is slightly larger than the headlights.

These are external decorative wings. Without them, the model will look unfinished.

This is the radiator grille trim. To give a better look, you can apply a drawing.



This is a set of seats, in order: the upper part of the front seat, the lower part of the front seat, and the rear seat.

Marker headlights located on the partition between the passenger compartment and the engine compartment.


These are the two parts needed to give the interior a good appearance.


Let's start assembling the car. We take the base and attach the sides to it. After assembly we should have the following:


We install the rear seat into the grooves in the side parts.


We need this part to attach the front seats.


We fasten the front seats. We fasten the flat part horizontally, and the convex part vertically.


Next, we attach the steering wheel and put on the “steering ring”

Next, insert the back wall into a special groove


We insert the “dashboard” into its rightful place.

Now let's put on the roof. You need to get into special holes.

Next, we install a partition between the passenger compartment and the engine compartment.

Next, install the side covers of the engine compartment.

Next, fold the sandwich. And put it in the right place

Next we install the hood.

Next we attach the headlights and dimensions to the partition

After that, put on the wheels and fix them. To fix it, you need to turn the plugs as shown in the photo.

Then we attach the outer wings. The car is assembled!









come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (4)
  1. feelloff
    #1 feelloff Guests January 29, 2012 10:21
    0
    wow you are so simple. give it all to you... design it yourself.
  2. sanasansey
    #2 sanasansey Guests January 29, 2012 07:25
    1
    To assemble this machine, you first need to cut it out; in order to cut it out of plywood, you need a template, not by hand, because you need to draw all the parts. So where is the diagram, scan the car parts.
    And there will be Ausgezeichnet! surprised
  3. 17771andre
    #3 17771andre Guests 13 March 2012 14:16
    1
    Author, indicate in the article that this is a stupid Chinese designer from the KUMKA company, in my opinion it costs 20 UAH. Otherwise you write as if you carved it yourself. A shame.....
  4. Penguin
    #4 Penguin Guests January 27, 2017 01:05
    1
    Do you have a drawing?