How to make a simple laser level from a pointer

How to make a simple laser level from a pointer

In construction and finishing, precision is important, which can be perfectly maintained using a laser level. This is an expensive tool, so purchasing it for a one-time repair is impractical. For small jobs, you can make a level yourself from a point laser pointer. It costs less than $3, which makes homemade a budget alternative to a specialized tool.

Materials for assembling a laser level


To make a homemade level you will need:
  • wooden block 30x30 –20 cm;
  • tube (according to the outer diameter and length of the pointer);
  • a motor from a children's toy;
  • crown battery;
  • crown terminal with wiring;
  • key mini switch;
  • a miniature mirror for cosmetic powder or lipstick;
  • ballpoint pen paste;
  • laser pointer.

For assembly you will use a hacksaw, a glue gun and a soldering iron. Ideally, in the future, use an adjustable tripod to install and adjust the level.

Assembling a level from a pointer


First you need to make the base for the level. A 30x30 mm block is suitable for this. It is enough to cut 20 cm.
How to make a simple laser level from a pointer

A tube made of thick cardboard (or plastic) is glued to it with a glue gun. It is selected in such a way that the pointer fits tightly into it. The length of the tube is approximately 15 cm.
How to make a simple laser level from a pointer

A motor from a children's car is glued to the end of the block farthest from the end of the tube. Its shaft is aligned with the focusing line of the pipe cavity.
How to make a simple laser level from a pointer

You need to assemble the motor power supply system. To do this, a mini switch is soldered to the wiring of the terminal installed on the crown.
How to make a simple laser level from a pointer

The battery and it are glued to the block. All that remains is to select the appropriate length of wires to solder it from the switch to the motor. A direct wire from the terminal is soldered to the second contact of the motor.
How to make a simple laser level from a pointer

Now you need to take a small mirror. It’s not difficult to find this - just peel it off in any unnecessary women’s cosmetic bag. The smaller and lighter it is, the better. You should find the center on it and draw a transverse line. An adhesive layer is applied over it and a ballpoint pen paste or Chupa Chups stick is glued in.
How to make a simple laser level from a pointer

The glued tube is placed on the motor shaft. If the mirror is balanced correctly, then when the engine is turned on, the design with a homemade blade almost does not vibrate.
How to make a simple laser level from a pointer

The level is ready, all that remains is to fix it on the tripod. This is done in different ways, depending on the design of the stand. In my case, you need to press the nut into the block and screw the tripod platform onto it.
How to make a simple laser level from a pointer

How to make a simple laser level from a pointer

How to make a simple laser level from a pointer

How to use


A pointer is inserted into the level tube.
How to make a simple laser level from a pointer

How to make a simple laser level from a pointer

Since it enters with force, its button is clamped and Light-emitting diode burns incessantly. Now, if you turn on the motor, the mirror rotating on its shaft will reflect the laser beam.
How to make a simple laser level from a pointer

As a result, the device will make a straight horizontal line from the point, illuminating the nearest perimeter of the walls.
How to make a simple laser level from a pointer

It can be used as a guide when laying tiles, hanging cabinets, attaching the eaves of a stretch ceiling, marking grooves, etc.
How to make a simple laser level from a pointer

The beam is very smooth.
How to make a simple laser level from a pointer

Don't forget about safety precautions!


  • Do not use a high power laser pointer (no more than 5 mW).
  • Avoid contact of the laser beam with your eyes.

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (5)
  1. Aoexander
    #1 Aoexander Guests 27 March 2019 13:39
    7
    Even cheaper and even simpler, a piece of polystyrene foam, glued with a laser ruler or construction tape, and put it in a plate of water. Amen.
    1. Guest Victor
      #2 Guest Victor Guests 27 March 2019 17:46
      4
      Do we “spread” the plate with water to the tripod to ensure the required line height?
  2. Uncle Vitya
    #3 Uncle Vitya Guests 28 March 2019 16:53
    5
    Instead of a bulky mirror, it is better to use a prism from any unnecessary CD drive
  3. Guest Sergey
    #4 Guest Sergey Guests 3 April 2019 23:42
    4
    I tried to make one, the line turned out to be curved
  4. Roll Up Your Sleeves
    #5 Roll Up Your Sleeves Guests 27 May 2020 22:29
    4
    "As a result, the device will make a straight horizontal line from the point..."
    No. The line will simply be straight, but horizontal, vertical or at any angle - depends on the plane of the device. And a plate of water won't help. The surface of the water will be flat, and the “ship” will float sideways, because it is not clear where its center of gravity is. And this is not to mention the rotating parts in “free floating” conditions. You'll get tired of running after the line all over the wall. Only rigid fastening to any platform, set horizontally (or vertically) using the same bubble level. Provided that the base plane of the device coincides with the plane of rotation of the mirror. But it’s better to avoid moving parts. There are options.