Copper deposition on non-metallic objects

Good afternoon In this article we will look at the process of electrochemical deposition of copper on conductive surfaces, and also try to coat a walnut with a copper layer.
Copper deposition on non-metallic objects

Will need


So, for the experiment we will need:
  • A non-metallic container - a beaker or a regular tray, where the deposition process will take place;
  • Water, preferably purified;
  • Copper sulfate (sold in garden stores);
  • Acid electrolyte for batteries (in car shops);
  • Charger 5 Volt, 0.3 Ampere;
  • 1 kOhm and 220 Ohm resistors to limit the supplied current;
  • Copper electrode.

Trying it on metal


Pour 100 grams of vitriol into a container, pour half a liter of water and add 70 grams of acid electrolyte.
Copper deposition on non-metallic objects

Mix and filter through a funnel and cotton pad.
Copper deposition on non-metallic objects

Install and secure the copper electrode:
Copper deposition on non-metallic objects

The plus power supply from charging will be connected to it. We make three taps from the minus: we solder a 1 kOhm resistor to the first, and a 220 Ohm resistor to the second.
Copper deposition on non-metallic objects

In this way we can conveniently regulate the supplied current.
When you turn on the charger, a chemical process called electrodeposition will begin.Under the influence of electric current, copper atoms on the positive contact are oxidized and dissolved in the electrolyte, then deposited on the negative. The power source current is selected at the rate of 1 Ampere per 100 cm² of surface to be coated.

Experience


First, let's coat a regular iron nail with copper. Coverage area – 10 cm².
Clean with sandpaper:
Copper deposition on non-metallic objects

We connect it to the power supply negative through a 1 kOhm resistor, and lower it into the solution. After 30 seconds, take it out and wipe it with a cotton pad. As a result, the layer turned out to be quite loose and erased.
Copper deposition on non-metallic objects

Now let's try to create a truly durable coating. To do this, we clean the nail and connect it through a 220 Ohm resistor, lower it into the solution for 10-15 seconds. Then we change the resistance to 1 kOhm and leave it for half an hour. Here's what happened:
Copper deposition on non-metallic objects

This time the coating turned out to be durable and left no marks on the disc at all.
After sanding, a small amount of copper still covered the nail.
Copper deposition on non-metallic objects

Let's try to coat a lead cake with copper. If you connect it through a resistance, even after a few minutes the result will be negligible.
Copper deposition on non-metallic objects

But as soon as you connect it directly, within a minute the cake will be completely covered with copper.
Copper deposition on non-metallic objects

If the coverage area is too small, then severe darkening can be observed:
Copper deposition on non-metallic objects

This phenomenon is called carbon deposits and is due to the fact that too much current flows across a given surface.

Coating a copper nut


We figured out the metals, but what about dielectrics, they don’t conduct current and the reaction simply won’t start. But there is a way out: we need to cover our object with conductive material. Graphite, from which leads for simple pencils are made, is excellent for the latter.
Copper deposition on non-metallic objects

Take the softest pencil.Soft pencils are marked with the letter “B”, and the number at the beginning indicates the degree of softness. A hard pencil works better with fine details. Let's color our nut.
Copper deposition on non-metallic objects

Copper deposition on non-metallic objects

Applying graphite using this method is a very tedious task, so construction stores sell a special graphite spray. He will cope with this task much faster.
After painting, we manually make a hole for the “twig” using a drill. Pour super glue into it, seal it with thick copper wire and fill it with graphite powder left over after decorating the nut.
Copper deposition on non-metallic objects

We connect the minus power to the wire through a 1 kOhm resistor. At this stage, you should not apply a large current, otherwise the copper layer will turn out loose, which is not good. After half an hour, the nut is slightly coated with copper and the resistance can be reduced to 220 Ohms.
Copper deposition on non-metallic objects

After some time, the growth of copper will slow down and the resistance will have to be reduced further
To do this, we will use a block of wood and a nichrome thread threaded like a snake onto screws along its edges.
Copper deposition on non-metallic objects

We set the resistance to 70 ohms.
When the copper completely covers the nut, set the value of the improvised resistor to 5 Ohms and leave the nut for another five hours for a thick and uniform coating.
During this time, the copper electrode was greatly depleted.
Copper deposition on non-metallic objects

All this copper settled on our nut, creating a rough layer.
Copper deposition on non-metallic objects

At the end of the process, the nut noticeably gained weight.

Treatment


To give the copper surface a nice shine, we will cover it with a patina and then polish it.
For this we need:
  • Ammonia, also known as ammonia solution;
  • Sulfur bomb (can be found in garden stores);
  • Chemical or disposable glass;
  • Fine-grit sandpaper.

Copper deposition on non-metallic objects

Pour a little ammonia into a glass and crumble a little sulfur.Place the nut there, as shown in the photo.
Copper deposition on non-metallic objects

The glass must be covered with something, because during the reaction, hydrogen sulfide is released - a gas with a pungent odor. After 20 minutes, the nut has darkened greatly; we take it out of the glass. We bite off the “twig” and bend the end into a loop with pliers.
Copper deposition on non-metallic objects

All that remains is to polish the nut with wet, rubbed sandpaper.
We thread the chain through the loop, and that’s it – the product is ready!
Copper deposition on non-metallic objects

And that's all for me. Happy experiments everyone!

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (1)
  1. Alexa
    #1 Alexa Guests 26 July 2018 16:04
    0
    A nail becomes coated with copper if it is simply dipped in a solution of copper sulfate. Standard test of Bordeaux mixture for acidity. If there is vitriol left in the solution that has not been quenched with lime, then the nail “turns red.”