How to etch a broken tap

How to etch a broken tap

When cutting threads in duralumin or aluminum, a mishap may occur and your tap will break, leaving a piece of debris inside the hole. Drilling tool steel out of duralumin-aluminum is incredibly difficult and means that the entire hole will be broken. There is a way in which the hole in the workpiece will remain intact, and the fragment can be removed without much difficulty.
The method is based on the difference in electrode potentials in different metals. In this regard, when aluminum (its alloys) come into contact with steel (iron), a galvanic couple is obtained. If such a pair is immersed in acid, galvanic corrosion of the steel will immediately begin.
Based on the size of a similar tap, you can estimate how deep the fragment lies.
How to etch a broken tap

Mark with a marker for clarity.
How to etch a broken tap

Everything is clearly visible under a microscope.
How to etch a broken tap

Needed for etching


  • Pack of citric acid powder 100 g.
  • Tap water 150-200 ml.
  • Utensils for pickling. I'll use stainless steel, but a regular enamel pan will work just fine.

How to etch a broken tap

Pour 2-3 teaspoons of citric acid into a cup and fill with water.
How to etch a broken tap

The electrolyte is ready.

Etching a piece of a tap in citric acid


Place the cup with the solution on the fire and lower the part with the broken tap into it.
How to etch a broken tap

How to etch a broken tap

Bring to a boil and reduce heat to minimum, but so that the liquid does not actively boil.
How to etch a broken tap

After 30 minutes.
How to etch a broken tap

After two hours of active etching.
How to etch a broken tap

We add water and acid, since the water boils away and the acid goes into the reaction.
How to etch a broken tap

How to etch a broken tap

After several hours, you can observe a black coating on the bottom of the dishes - the result of a chemical reaction.
How to etch a broken tap

Three hours passed and the tap was already noticeably burned.
How to etch a broken tap

After five hours of etching, nothing is visible in the groove.
How to etch a broken tap

We managed to extract the fragment of the tap by tapping.
How to etch a broken tap

The minutes were written down on a piece of paper, after which the condition was checked, plus water was added and citric acid was added.
How to etch a broken tap

With a similar tap you can see what happened to the fragment after the chemical reaction.
How to etch a broken tap

This is a simple, but quite time-consuming method. It’s good when the part is small in size and fits perfectly in a saucepan. It is more difficult when the part is massive.

Watch the video


Watch the video for the complete and detailed process.
come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (3)
  1. ku
    #1 ku Guests 27 June 2018 16:16
    1
    what kind of person do you have to be... to break the tap
  2. Egor
    #2 Egor Guests 27 June 2018 20:22
    4
    It will be much faster if you use a solution of nitric acid
  3. Buba
    #3 Buba Guests 12 November 2019 13:43
    0
    Need nitrogen