Headlight lens casting technology

When restoring cars and motorcycles, the problem arises in finding original lenses for headlights. If you can’t buy them, you can cast the lens yourself. It's not cheap, but it's the only way out of the situation. This method is applicable provided that you have one original lens that can be copied.
Headlight lens casting technology

Materials:


  • two-component silicone for molds;
  • synthetic clay;
  • separator for silicone molds;
  • transparent two-component casting resin.

Lens casting


For casting, you need to make a lens mold from two-component silicone. It allows you not only to recreate the contour of the headlight, but also to completely replicate the fine relief and even shine on a replica. Silicone components A and B are mixed in proportions according to the instructions. You need to prepare enough composition to completely fill the existing original lens.
Silicone is prepared in a clean container without dust, much less dried dirt. After kneading, the composition is installed in a vacuum chamber to remove air bubbles. If this is not done, then it will not be possible to transfer the gloss of the original to the replica.
Headlight lens casting technology

The original lens is perfectly cleaned, there should not even be a fingerprint on it.It is installed in a clean container without a bottom on a thick base of synthetic clay. It needs to be lightly pressed into the clay to seal the internal cavity from silicone. The clay serves as the bottom of the container; in addition, it will hold the glass, preventing its possible floating in the silicone. On a clay lining on the side of the headlight, several indentations are made with your finger, which will later help center the halves of the injection mold. The lens must be filled completely.
After the silicone hardens, the mold is turned over. The clay backing is removed down to the last piece. After this, the back side of the lens glued into silicone is wiped again.
Headlight lens casting technology

The silicone, cleared of clay, is lubricated with a separator. This prevents the two halves of the mold from sticking together in the future.
Headlight lens casting technology

Silicone is poured from above on the back side of the lens. This time it will be needed less. Naturally, before this it is prepared in a vacuum chamber.
Headlight lens casting technology

As soon as the second portion of silicone hardens, the finished mold halves with the original lens located inside are removed from the container.
Headlight lens casting technology

Headlight lens casting technology

To make them slide out more easily, you can add any silicone-compatible lubricant or water under the walls.
Next, the halves of the mold are separated and the original lens is removed. In order not to spoil the casting material, they must be carefully inspected for defects.
Optically transparent casting resin is mixed according to the instructions. The composition is placed in a vacuum chamber to remove air bubbles.
The mold halves are assembled and laid sideways. They move apart a little, and resin is poured into the gap formed.
Headlight lens casting technology

Then the mold is closed and clamped with a clamp, but without squeezing.
Headlight lens casting technology

After the resin has cured, the replica lens is removed. In this case, the form can be reused.
Headlight lens casting technology

This method is also applicable for casting other rare parts that cannot be purchased due to their rarity. If you use high-quality resin when copying a lens, the headlight will never turn yellow and will be equally strong in both cold and hot weather.
Headlight lens casting technology

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (0)