New life for an old music center

New life for an old music center

Many people have outdated stereo systems in their closets and garages. They are not used because cassettes have long since become obsolete, and CDs are also almost dead. Well, such a center is not provided for a flash drive. Although the entire sound path with power amplifier and speaker systems is in excellent condition.
There is a way out of this situation and it is not as difficult as it might seem: we buy at AliExpress built-in MP3 player - http://ali.pub/3w9mcs. We install it in the center body. And after this modification, the old music center will be able to read any flash drive. All modules have a remote control included, and some have Bluetooth, which will significantly expand the functionality of the entire center to the maximum.

Modernization of an old music center


A place in the upper part was determined for the location of the player.
New life for an old music center

From the back you can see that there is enough space inside to install the module.
New life for an old music center

Finding inputs and power


To operate the built-in player, you need a 5V power supply and an audio input. If you have “AUX” inputs at the back, then there are no special problems - connect to them and you’re done.
New life for an old music center

Let's connect them to the back of the board.
New life for an old music center

If not, you'll have to do a little searching for connections on the board itself. Usually everything is simple: there is one train coming from the decks.
New life for an old music center

And next to it should be all the designations of each contact.
New life for an old music center

We are interested in: general, left and right input (“L”, “R”). Connect to them if your center is not equipped with “AUX”. I will connect to “AUX”.
For the module to operate, you need not only audio inputs, but also 5 V power. It is also easy to find on the board, since everything is labeled. Either on the same cable from the decks, or you can find it next to the power amplifier.
New life for an old music center

Installation and connection


It doesn’t matter how to make a groove for the module; everyone decides for themselves. You can use a soldering iron as in this case, after first drawing a line with a marker.
New life for an old music center

Next, we cut off the deposits with a utility knife and try on the module.
New life for an old music center

If everything fits, solder the wires. Two for power and three for stereo sound output.
New life for an old music center

There is also nothing complicated about it - everything is signed on the player.
And install it in the groove.
New life for an old music center

We fix it with self-tapping screws.
New life for an old music center

Solder the power wires.
New life for an old music center

Solder the sound to AUX.
New life for an old music center

We close the music center and check.
New life for an old music center

Light-emitting diode The player lights up, which means there is power. We switch the center to AUX mode and insert a flash drive into the player. We turn it on and control it using the remote control.
New life for an old music center

Everything works perfectly! The sound is clear.
Such a simple and not very expensive modification will return the music center to operation and it will serve you faithfully for many years.
It is highly advisable to purchase player modules with bluetooth (http://ali.pub/3w9mcs), and send sound to it from any device: be it a smartphone, tablet or laptop.

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (4)
  1. Martin
    #1 Martin Guests 15 October 2019 20:15
    1
    I have two tape recorders that already work this way. One in the garage, the second in the kitchen))))
  2. Guest Alexander
    #2 Guest Alexander Guests October 16, 2019 20:00
    3
    All Chinese boards are very noisy, it’s easier to buy a receiver with MP-3 and connect it to the amplifier input. I have already bought a third board and they all make the same noise, and the sound quality is lower than from the receiver.
    1. Konstantin
      #3 Konstantin Guests 17 October 2019 15:12
      1
      Do you think the MP-3 receiver is not Chinese?
    2. Ivan
      #4 Ivan Guests 24 October 2019 13:31
      0
      Quite a known problem. Those who make bluetooth speakers add a 5V dc-dc converter as a power decoupler between the bluetooth module and the amplifier and the noise disappears.