Amplifier based on TEA2025b chip

Now there is a huge variety of audio amplifier circuits on microcircuits, for any needs, for any supply voltage, with different output powers. Microcircuit amplifiers are easy to create and do not require special settings, unlike transistor amplifiers, but they also have good characteristics. That is why microcircuit amplifiers are now used everywhere: in car radios, computer speakers, televisions, and music centers. One of these chips is the fairly popular TEA2025b. It can be found in many computer speakers or portable portable acoustics. This microcircuit provides an output power of 1-2 watts, consumes a small current and does not require a radiator, while its power is quite enough to sound a small room. Another advantage of TEA2025b is that it contains two channels at once, i.e. To build a stereo amplifier, just one microcircuit is enough.

Amplifier circuit

The circuit does not contain any expensive or scarce parts.The capacitors C3 and C4 in it are isolation capacitors, although the amplifier is not of the Hi-Fi category, it is still advisable to use film ones. If desired, their capacitance can be increased from 220 nF to 0.5 - 1 µF, which will slightly increase the level of low frequencies. P1/A and P1/B in the diagram are a double variable resistor (potentiometer), with its help the volume is adjusted. Its rating is not so critical; you can take it in the range of 10-50 kOhm. Diode D1 serves to protect the circuit from polarity reversal, because if a voltage of the wrong polarity is applied to the microcircuit, it will immediately burn out. The diode will prevent such accidents. All capacitors in the circuit must be taken at a voltage no less than the supply voltage of the amplifier. Speakers may have an impedance of 4 ohms or higher. It is worth considering that the lower the speaker impedance, the greater the amplifier power will be. The best option is 8 ohms. During operation, the microcircuit may heat up slightly, this is normal, because its case does not provide for the installation of a radiator.

Amplifier assembly on TEA2025b chip

The creation of any electronic device begins with the manufacture of a printed circuit board; you can make it at home using the LUT method.

Download the board:

pechatnaya-plata.zip [19.5 Kb] (downloads: 1619)

A file with a drawing of the printed circuit board is attached to the article; there is no need to mirror it before printing. The board is made on a piece of PCB measuring 60x35 mm. The LUT method has been described more than once on the Internet; I will give only a few photographs of the process of creating a printed circuit board.

After the board is ready, you can solder parts into it. It is advisable not to solder the power wires and outputs to the speakers into the board, but connect them using terminal blocks. For convenience, the signal wire is connected to the board using a 3.5 jack connector.The wire from the sound source to the amplifier board must be shielded, otherwise extraneous noise cannot be avoided.

A few words about nutrition. The optimal supply voltage for this amplifier is 9 volts. It will work starting from 3 volts, but the output power will be significantly less. In rest mode, i.e. when no signal is being input, the amplifier consumption is approximately 40-50 mA at a supply voltage of 9 volts. When a signal is applied to the input, consumption increases to a level of 150-200 mA. Before turning it on for the first time, you must turn off the speakers, plug an ammeter into the supply wire and measure the current consumed by the circuit. If it is significantly higher than 50 mA, and the microcircuit heats up quickly, then you need to look for an error in the installation. If the current consumption is completely zero, then the circuit is not working, you also need to look for the error and check that the power supply is connected correctly. If, when you first turned it on without speakers, nothing exploded, and the current consumption is normal, then you can connect the speakers and send a signal to the input. The signal source for the amplifier can be a player, computer, telephone, or any device that has a linear output.

Thus, on the TEA2025b chip you can build a simple amplifier that does not require tuning. It consumes little current and has low heat generation, which means it belongs in portable audio systems or simple computer speakers where high-quality sound is not required. Happy build!

come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
3+three=
Comments (9)
  1. Guest Vladimir
    #1 Guest Vladimir Guests 17 April 2018 18:42
    1
    Thanks for the stamp...
  2. Guest Alexey
    #2 Guest Alexey Guests April 28, 2018 11:56
    0
    It’s cheaper and easier to order from China. The board is unsuccessful - the volume control and the socket are located close to each other, it’s generally not clear what kind of case or design this was all made for?
  3. Ivan
    #3 Ivan Guests 1 June 2018 22:39
    3
    Everything is fine. Good, competent development. Volume control and input plug - what's wrong? Nearby, so what?
    Respect to the author.
  4. Ivan
    #4 Ivan Guests 1 June 2018 22:46
    1
    For complete beauty, install paper capacitors C3 and C4 (type K73-17), and 1000 uF for the outputs
  5. Edward
    #5 Edward Guests 26 June 2018 21:22
    2
    In theory, this microcircuit is intended to be installed on a radiator, it has two terminals on each side, they are connected together, these are its heat sink terminals. I have seen this microcircuit on a radiator in cassette recorders more than once
  6. Raf
    #6 Raf Guests December 28, 2018 09:44
    3
    Can you provide a detailed list of everything included for assembly?
  7. Daniil Petriv
    #7 Daniil Petriv Guests January 23, 2019 12:50
    0
    Please provide an appendix with details
  8. Evgen
    #8 Evgen Guests 24 February 2019 15:13
    1
    Tell me, 1 leg bridge mode (mono) if shorted to ground as in the ka2206 circuit, will it work?
    1. 3D
      #9 3D Guests 27 October 2020 22:19
      1
      Yes! Since the KA2206 and TEA2025B microcircuits are analogous to both microcircuits!