Quick desoldering of SMD components using an iron

Quick desoldering of SMD components using an iron

SMD parts are increasingly used in production, as well as among radio amateurs. It is more convenient to work with them, since there is no need to drill holes for leads, and the devices turn out to be very miniature.
SMD components can be completely reused. Here again the obvious superiority of surface mounting appears, because it is much easier to solder small parts. They are very easy to blow off from the board with a special soldering hair dryer. But if you don’t have one at hand, then an ordinary household iron will help you out.

Dismantling SMD parts


So my LED bulb is burned out and I won't fix it. I will solder it into parts for my future homemade products.
Quick desoldering of SMD components using an iron

We disassemble the light bulb and remove the top cap.
Quick desoldering of SMD components using an iron

We take out the board from the base of the base.
Quick desoldering of SMD components using an iron

Quick desoldering of SMD components using an iron

We unsolder the attached components and parts, wires. In general, there should be a board with only SMD parts.
Quick desoldering of SMD components using an iron

Quick desoldering of SMD components using an iron

We fix the iron upside down. This must be done firmly so that it does not tip over during the soldering process.
Another good thing about using an iron is that it has a regulator that will quite accurately maintain the set temperature of the sole surface.This is a huge plus, since surface components are very afraid of overheating.
We set the temperature to about 180 degrees Celsius. This is the second mode for ironing clothes, if my memory serves me correctly. If soldering does not work, gradually increase the temperature.
Place the light bulb board on the sole of the inverted iron.
Quick desoldering of SMD components using an iron

We wait 15-20 seconds until the board warms up. At this time, we wet every part with flux. The flux will not cause overheating, it will be a kind of assistant during desoldering. With it, all elements can be removed without difficulty.
Quick desoldering of SMD components using an iron

Once everything has warmed up well, all the parts can be brushed off the board by hitting the board on some surface. But I will do everything carefully. To do this, we will take a wooden stick to hold the board in place and use tweezers to disconnect each component of the board.
Bare board at the end of work:
Quick desoldering of SMD components using an iron

Soldered parts:
Quick desoldering of SMD components using an iron

Everything is working, nothing burned.
What can be made from them? Of course it's up to you to decide!
I'll make a flashlight with a Krona battery.
Quick desoldering of SMD components using an iron

Quick desoldering of SMD components using an iron

This method will allow you to very quickly solder any boards with SMD parts. Take it into your arms, friends!

Watch the video on desoldering SMD parts


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
4 minus one =
Comments (2)
  1. Guest Evgeniy
    #1 Guest Evgeniy Guests 5 April 2018 23:37
    4
    lamp 12 V low beam ........ replaces the iron well
    1. Guest Sergey
      #2 Guest Sergey Guests 11 March 2019 14:41
      0
      And the lamp replaces the sun. Once you work with it, your eyes will burn for a very long time.