Powerful homemade Wi-Fi antenna

The Internet today is as necessary as air, and modern life without it is simply unthinkable. And how joyful it is to realize that there are more and more free access points using Wi-Fi technology. But not everyone manages to use them, because the signal is not strong enough. In such a situation, the FA-20 panel antenna will help out, which today we will suggest you make with your own hands.
In fact, this device is quite simple and will not cause any difficulties in manufacturing even in an ordinary apartment. But the benefits from it will be quite noticeable, and maybe even some radio amateurs will be encouraged to take up the manufacture of such equipment seriously.
Powerful homemade WiFi antenna

Antenna characteristics


The panel antenna consists of 2 main parts - a reflector and vibrators. The line of vibrators is connected by a common contact, from which a coaxial cable is led out, leading to the jack of the external antenna of the Wi FI router, mounted on the back of the device. The antenna works as an amplifier, which can be judged by comparing the signal power from the standard antenna of the router (the author used tp-link TL-WN722N) - 5db, and from the FA-20 - 22db.
Necessary materials:
  • Foil textolite one-sided or getinaks, 430x200 mm, thickness - 1.5 mm;
  • A piece of sheet metal (best galvanized), 435x205 mm, thickness 0.5-1 mm;
  • TV coaxial cable RG-8X 50 Ohm;
  • Drawing template of antenna vibrators printed on vinyl film;
  • Photoresist;
  • Ferric chloride for etching boards;
  • A can of aerosol varnish for textolite;
  • Soda, acetone or alcohol;
  • Hardware: 3 mm bolts – 12 pcs., nuts – 32 pcs.

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Tools:
  • A drill with a cutting disc for cutting getinax;
  • Drill with drill 3-3.5 mm;
  • Soldering iron with solder;
  • Painting knife, scissors;
  • Pliers, metal scissors;
  • Construction rubber roller for rolling films;
  • Bath for etching the antenna board;
  • A piece of glass and an ultraviolet lamp for photolithography;
  • Hairdryer or iron to warm up the photoresist;
  • Sandpaper-zero;
  • Hot glue gun;
  • Core, hammer;
  • Metal ruler for marking holes.

Making a Wi-Fi antenna


Stage one - making a panel of vibrators


We mark a sheet of foil PCB to the size of our antenna, and cut it out with a cutting disc of a drill. This procedure can also be performed with a regular paint knife, making cuts along the marking line on both sides of the sheet, and then breaking them off by hand.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We print a template of the antenna vibrators on transparent film for inkjet printers. It will come out of two sheets, which are then easily connected to each other.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

To etch using photoresist technology, it is necessary to prepare the foil side of the getinax by cleaning it with a zero. You can degrease surfaces using acetone or alcohol.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We place the photoresist film on the getinax, cutting it to size with scissors. We remove the protective layer and glue the photoresist, getting rid of air bubbles by rolling with a rubber wallpaper roller.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

After this, we apply the vibrator template film and cover it with ordinary glass. We use an ultraviolet lamp to illuminate the photoresist. The holding time for different manufacturers of this material differs. The author needed 5 seconds for his film, ordered from China. for each processed area of ​​the board.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Now it is necessary to additionally heat the photoresist so that it firmly adheres to the surface of the getinax. We remove the template, a sheet of glass, and heat the film with a hairdryer or iron through the paper. Remove the top protective layer of photoresist.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We wash off the unexposed photoresist in a baking soda solution, placing the getinax plate in the bath. After a few minutes, remove any remaining film with a used toothbrush.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Getinax is ready for pickling. We dilute ferric chloride in warm water and dip the plate into a container with the solution. It must be stirred periodically.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We saturate the old lye solution with soda ash and place the plate in it to get rid of the remaining photoresist. We wash the resulting board with plain water.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We mark the centers of the rectangles of the vibrators on the board, and use a core to drill them. The hole must be made for the mounting bolts 3 mm. The author used a step or precision conical drill, which is convenient for removing burrs.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Stage two - preparing the reflector


From a piece of galvanized sheet metal, which is the most resistant to corrosion, we cut out a copy of our vibrator plate. The holes for fastening the bolts can be easily transferred to the sheet metal by making notches with the same drill. We drill holes on the tin through a wooden lining.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We tighten the bolts with two nuts on the back side of the plate, making the required gap between the reflector 3 mm, and the total distance between the vibrators and the reflector 6 mm. We secure the tin using the third nut.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

In the upper part of the reflector we make a hole for a coaxial cable, the central core of which must be soldered to the vibrator plate, and the braid to the reflector.
We solder the second end of the cable in place of the external antenna to the router. We attach it to the reflector from the back of the antenna using hot glue.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

We protect the front side of the vibrator board from oxidation with aerosol colorless varnish.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

For home use, this antenna can be placed on a windowsill or balcony. If you plan to use it outdoors, any bracket leading to a mast on the roof or outside the window can easily be attached to the reflector.
Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Powerful homemade WiFi antenna

Watch the video


come back
Comment
  • bowtiesmilelaughingblushsmileyrelaxed relaxedsmirk
    heart_eyeskissing_heartkissing_closed_eyesflushedrelievedsatisfiedgrin
    winkstuck_out_tongue_winking_eyestuck_out_tongue_closed_eyesgrinningkissingstuck_out_tonguesleeping
    worriedfrowninganguishedopen_mouthgrimacingconfusedhushed
    expressionlessunamusedsweat_smilesweatdisappointed_relievedwearypassive
    disappointedconfoundedfearfulcold_sweatperseverecrysob
    joyastonishedscreamtired_faceangryragetriumph
    sleepyyummasksunglassesdizzy_faceimpsmiling_imp
    neutral_faceno_mouthinnocent
5+two=
Comments (11)
  1. Anatoly Batin
    #1 Anatoly Batin Guests March 13, 2018 08:03
    2
    Why so many troubles, the lead singer never worked, why are there 8 bolts or is it for beauty.
  2. Izhat
    #2 Izhat Guests 13 March 2018 13:55
    5
    Why are you fooling people? Coef. amplification17 dB??? Not all antennas can do this. amplification Here it is at most 2 dB. How to calculate the dimensions, from the ceiling7 Connecting vibrators is nonsense! Calculate the antenna for 900 MHz. (Phasing antennas).
  3. Izhat
    #3 Izhat Guests 13 March 2018 14:02
    1
    900 MHz is for mobile. communications. Judging by the size, your ant. for this. WI-FI at 2-5 GHz. Dimensions of mountains less.
  4. Guest Andrey
    #4 Guest Andrey Guests 14 March 2018 18:21
    0
    Is it only receiving or can it broadcast a signal?
  5. Guest Andrey
    #5 Guest Andrey Guests 14 March 2018 18:24
    0
    and in general the biquadrat is simpler and has the same effect, and in the USSR there was a butterfly antenna
  6. Evgen
    #6 Evgen Guests March 16, 2018 06:35
    7
    nitro paint or nitro varnish + copper sulfate, otherwise buy a printer, buy a photoresist film, an ultraviolet flashlight, maybe even spray the getinax yourself?
    1. zor
      #7 zor Guests March 29, 2018 03:34
      1
      Yes, I thought so too, they came up with some kind of films... varnish is much simpler)
  7. Passerby.
    #8 Passerby. Guests March 19, 2018 10:06
    2
    Somehow too simple.
  8. Anton
    #9 Anton Guests 9 April 2018 19:28
    5
    What are the template parameters for printing on film? Maybe there is a file?..
  9. Alex
    #10 Alex Guests March 15, 2020 10:50
    1
    Are the reflectors and the vibrator connected to each other? Short in between? Is the ground connected to the central core?
  10. ujcnm
    #11 ujcnm Guests July 2, 2021 09:20
    0
    Why translate so much textolite - a whole sheet... These squares can be made separately and stripes separately. Maybe not strips, but thick copper wires between the squares. And in general, textolite is expensive for this. Connect the cans into squares with a 2mm copper conductor...