12V Portable Disc Sander
Work in a home workshop is varied. Sometimes it is necessary to grind or sharpen some part or workpiece. But there is no sharpening machine, and the grinder is missing. A portable tool, assembled almost on your knees, can help out in such a situation.
The disc sander featured in today's video is completely portable. In addition, if the voltage with a fixed network is 220 V, this tool will come in handy. After all, it is powered by a 12 V battery.
[media=https://www.youtube.com/watch?v=Vy57B7h_Zas]
The operating principle is based on the transmission of torque from the engine to the grinding disc. Using such a tool, you can sharpen scissors or a knife, or process a wooden or plastic workpiece.
Materials:
For the base of our grinder you will need a handle from a drill or hammer drill with a clamping clamp. It should be of a size suitable for clamping the engine housing.
Next, we take a 12V motor and select a cable sleeve for it with a threaded hole at one end and an open clamping hole at the other. This element is necessary for clamping the grinding disc, since there are no threads in the motor shaft itself.
We clamp the sleeve on the engine shaft and fasten it securely in the handle clamp.
We make a hole in the plastic collar of the handle with a drill with a diameter of 5-6 mm. You will need it to thread the wires through the handle.
We divide a section of a paired cable into separate wires, strip the ends and tin them with flux and solder. We try on the switch button in a convenient place on the handle. We cut one wire, and from two of its parts we make wiring to the button. We solder all contacts securely. Attach the switch button using hot glue.
Due to the low voltage, the author of the video chose to connect the device via a 2.5x5.5 DC power connector. These are often used on power supplies for laptops and netbooks. We solder an extension cord with a plug from this connector to the contacts brought out through the handle. We insulate the twisting area with electrical tape or heat-shrinkable casings, burning them with a lighter.
We take a sheet of thin but elastic sheet metal and use a compass to mark a circle with a diameter of 100 mm.Using scissors, we cut out the disk and make a small hole in its center for the pressure screw for the sleeve.
From sandpaper on a fabric base, cut out a circle, previously marked along the disk. Using scissors, cut out a space in the center for the screw head.
Glue the sandpaper to the disk with superglue, trimming the protruding edges.
We clamp the sleeve on the motor shaft with hexagon screws. We screw the disk to the sleeve with a screwdriver, squeezing it from the back with an adjustable wrench.
The sander is ready, now you can try to sand or sharpen something!
The disc sander featured in today's video is completely portable. In addition, if the voltage with a fixed network is 220 V, this tool will come in handy. After all, it is powered by a 12 V battery.
Watch the video
[media=https://www.youtube.com/watch?v=Vy57B7h_Zas]
Brief characteristics of a homemade grinder
The operating principle is based on the transmission of torque from the engine to the grinding disc. Using such a tool, you can sharpen scissors or a knife, or process a wooden or plastic workpiece.
What do we need for work?
Materials:
- Simulation DC Motor 775;
- Handle from a drill or hammer drill;
- 12 V battery;
- Cable sleeve with hidden bolts;
- Switch button;
- Wires with insulated terminals;
- Heat-shrinkable tubes or electrical tape;
- Bolts, nuts, washers.
- Tools:
- Drill or screwdriver with a Phillips head;
- Drill for the diameter of the engine shaft;
- Soldering iron;
- Metal and regular scissors;
- Sandpaper, compass;
- Pliers, knife, pencil;
- Matches or lighter;
- Quick setting or superglue.
Assembling a sander - step-by-step master class
Engine installation
For the base of our grinder you will need a handle from a drill or hammer drill with a clamping clamp. It should be of a size suitable for clamping the engine housing.
Next, we take a 12V motor and select a cable sleeve for it with a threaded hole at one end and an open clamping hole at the other. This element is necessary for clamping the grinding disc, since there are no threads in the motor shaft itself.
We clamp the sleeve on the engine shaft and fasten it securely in the handle clamp.
Electrical diagram
We make a hole in the plastic collar of the handle with a drill with a diameter of 5-6 mm. You will need it to thread the wires through the handle.
We divide a section of a paired cable into separate wires, strip the ends and tin them with flux and solder. We try on the switch button in a convenient place on the handle. We cut one wire, and from two of its parts we make wiring to the button. We solder all contacts securely. Attach the switch button using hot glue.
Due to the low voltage, the author of the video chose to connect the device via a 2.5x5.5 DC power connector. These are often used on power supplies for laptops and netbooks. We solder an extension cord with a plug from this connector to the contacts brought out through the handle. We insulate the twisting area with electrical tape or heat-shrinkable casings, burning them with a lighter.
Sanding disc and final assembly of the sander
We take a sheet of thin but elastic sheet metal and use a compass to mark a circle with a diameter of 100 mm.Using scissors, we cut out the disk and make a small hole in its center for the pressure screw for the sleeve.
From sandpaper on a fabric base, cut out a circle, previously marked along the disk. Using scissors, cut out a space in the center for the screw head.
Glue the sandpaper to the disk with superglue, trimming the protruding edges.
We clamp the sleeve on the motor shaft with hexagon screws. We screw the disk to the sleeve with a screwdriver, squeezing it from the back with an adjustable wrench.
The sander is ready, now you can try to sand or sharpen something!
Similar master classes
Particularly interesting
Comments (0)